产品列表
路沿石钢模具
盖板钢模具
标志桩钢模具
隔离墩钢模具
化粪池钢模具
U型槽钢模具
遮板钢模具
道轨模具
护坡钢模具
制砖机
检查井钢模具
声屏障钢模具
防撞墙钢模具
围墙板模具
方涵模具
锚杆框架梁模具
配重块模具
水泥三盘模具
水泥预制件模具
      新闻中心
· 预制检查井模具的制作步骤
· 检查井模具的基本结构
· 选购检测井模具的注意事项
· 检查井模具的独特设计均可定...
· U型槽模具的施工方法
· 隔离墩模具的巧妙设计及防撞...
      联系我们

电话:0312-8103818 18803129528
传真:0312-8103818
在线QQ:107108222
地址:保定市城东工业区

     新闻中心

U型槽模具的施工方法

[关闭该页][设为首页][添加收藏][发送朋友][打印][ ]

      U型槽模具有两种材质,一种是塑料的,另一种是用钢板焊接建造的,U型槽模具具有坚固耐用的特点,而且同其他材料相比,他具有节省钢材,成本更低等优点。由于U型槽都是一些水泥制品,其压力大重量大,所以在选用的时候钢板厚度需要注意,U型槽钢模具的尺寸规格有经常使用的几种,同时这种U型槽尺寸规格小的可以选用薄一点的钢材,超过1米的模具在使用薄的钢材比较不合适,应该选用5MM厚一点的钢材,选用钢模具生产能够降低一定的生产困难,同时这种钢模具使用寿命很长,可以大大的提升产品的生产效率。

There are two kinds of materials for U-groove die, one is plastic, the other is welded with steel plate. The U-groove die has the characteristics of ruggedness and durability. Compared with other materials, it has the advantages of saving steel and lower cost. Because U-groove is some cement products, its pressure is large and its weight is heavy, so the thickness of steel plate should be noticed when choosing. The size specifications of U-groove steel die have several kinds that are often used. At the same time, the size specifications of U-groove steel can be selected to be a little thinner. Dies over 1 meter are not suitable for using thin steel. Steel with a thickness of 5MM should be selected and steel die should be selected. Production can reduce certain production difficulties, at the same time, the service life of this steel die is very long, which can greatly improve the production efficiency of products.

     一般U型槽模具是u型槽预制成型,如果使用在一些大型建筑物底部支撑的作用,根据使用的u型槽模具尺寸调整,首先,会增加钢板的厚度,然后将增加钢板的宽度,通常我们使用u型槽在高速公路上的钢板厚度,模具是在2 - 4厘米,宽度在500x400,规范也非常多,所以的厚度大的u型槽钢模具将在3到5厘米,用于大型的建设好,独立桥墩砖的工作由原位生产方式,现在很多施工现场的方法,和一些生产方法是建设单一钢铁架标签的位置,然后在钢管的支持,然后在模板上的接头,内和外板,焊接,将所有的焊接螺钉孔和加强筋,然后灌浇混凝土。这些程序之前组装后的钢板,中间的板的安装,中间有设置自动扶梯或电梯,方便施工人员及时容易去除内部脱模模板。

Usually U-groove die is prefabricated u-groove. If it is used to support the bottom of some large buildings, it can be adjusted according to the size of U-groove die. First, the thickness of steel plate will be increased, and then the width of steel plate will be increased. Usually, we use U-groove in the thickness of steel plate on expressway. The die is 2-4 cm, the width is 500 x 400, and there are many specifications. The thick U-shaped channel steel die will be used for large-scale construction. The work of independent pier bricks will be done by in-situ production. Now many construction site methods and some production methods are to construct the location of a single steel frame label, then support the steel pipe, then weld the joints on the template, the inner and outer plates, weld all the welding screw holes and reinforcement bars, and then pour and mix them. Condensate. These procedures are assembled before the steel plate, the installation of the middle plate, and the installation of escalators or elevators in the middle. It is convenient for the construction personnel to remove the internal demoulding template in time and easily.


【上一个】 检查井模具的独特设计均可定做 【下一个】 隔离墩模具的巧妙设计及防撞功能


 · U型槽模具的施工方法

检查井钢模具,检查井模具,预制检查井模具——保定乐丰钢模具厂 |隔离墩模具|流水槽模具|标志桩模具|检查井模具|隔离墩模具|化粪池模具|水泥防撞墙模具|护坡模具|排水沟模具|