产品列表
路沿石钢模具
盖板钢模具
标志桩钢模具
隔离墩钢模具
化粪池钢模具
U型槽钢模具
遮板钢模具
道轨模具
护坡钢模具
制砖机
检查井钢模具
声屏障钢模具
防撞墙钢模具
围墙板模具
方涵模具
锚杆框架梁模具
配重块模具
水泥三盘模具
水泥预制件模具
      新闻中心
· 预制检查井模具的制作步骤
· 检查井模具的基本结构
· 选购检测井模具的注意事项
· 检查井模具的独特设计均可定...
· U型槽模具的施工方法
· 隔离墩模具的巧妙设计及防撞...
      联系我们

电话:0312-8103818 18803129528
传真:0312-8103818
在线QQ:107108222
地址:保定市城东工业区

     新闻中心

选购检测井模具的注意事项

[关闭该页][设为首页][添加收藏][发送朋友][打印][ ]

    检测井模具=是按照客户所需求规格定制,按照检测井模具在污水、雨水、排水、小区、市政等使用的原则来说。检测井模具同属于检查井钢模具的范围,根据检测井模具的尺寸以及规格定制的模板需要符合检查井构件的要求,保证工程能够使用到规格正确的模板。检查井模具正确操作步骤为先将内模放置好,然后放外模,再将混凝土灌入内外模中间的位置,使用小型振动棒进行震动,这样能够保证混凝土检查井外表的光滑度,在经过6-8小时晾晒就可以脱模了。在脱模的时候,先将圆形井的内模拆掉,然后再拆井体的外模,这样一套混凝土检查井就做好了。

Inspection well mold = it is customized according to the specifications required by customers, and according to the principle of using inspection well mold in sewage, rainwater, drainage, community, municipal, etc. The inspection well mold belongs to the scope of inspection well steel mold. The template customized according to the size and specification of inspection well mold needs to meet the requirements of inspection well components to ensure that the project can use the template with correct specification. The correct operation steps of the inspection well mold are: first place the internal mold, then place the external mold, then pour the concrete into the middle of the internal and external mold, and use a small vibrator to vibrate, so as to ensure the smoothness of the concrete inspection well surface, and the mold can be removed after 6-8 hours of air drying. When demoulding, first remove the internal formwork of the circular well, and then remove the external formwork of the well body, so that a set of concrete inspection well is completed.
    我厂专业生产检测井模具,有多年的制作经验,专业制作各种不同型号、不同产品规格的检测井模具,可以满足客户的不同需求,产品型号种类齐全。检测井模具的尺寸基本上有三种常用的,和大多数轮检查井模具大概一样,内径分别为1米,三种1.5米和1.25米等,在壁厚超过20厘米,除了上述检验轴模具收敛基本的直径是70厘米。检测井模具定期大小其实并不多,主要是考虑到对每个规格的数量需求以及各种规格的生产分为几个部分。检测井模具尺寸多样式多,选购钢模具一定要注意产品的质量,模具的质量主要体现在颜色,重量,和外观整齐度,这个一定要把控好。

Our factory specializes in the production of inspection well mold, with many years of production experience, specializing in the production of different models, different product specifications of inspection well mold, can meet the different needs of customers, product types are complete. There are basically three kinds of common sizes of inspection well mould, which are about the same as most wheel inspection well moulds. The inner diameter is 1 m, three kinds are 1.5 m and 1.25 m respectively, and the wall thickness is more than 20 cm, except that the basic convergence diameter of inspection shaft mould is 70 cm. In fact, the regular size of inspection well mold is not much, mainly considering the quantity demand of each specification and the production of various specifications is divided into several parts. There are many sizes and styles of inspection well mould. When purchasing steel mould, we must pay attention to the quality of the product. The quality of the mould is mainly reflected in the color, weight and appearance uniformity, which must be well controlled.


【上一个】 检查井模具的基本结构 【下一个】 检查井模具的独特设计均可定做


 · 选购检测井模具的注意事项

检查井钢模具,检查井模具,预制检查井模具——保定乐丰钢模具厂 |隔离墩模具|流水槽模具|标志桩模具|检查井模具|隔离墩模具|化粪池模具|水泥防撞墙模具|护坡模具|排水沟模具|