产品列表
路沿石钢模具
盖板钢模具
标志桩钢模具
隔离墩钢模具
化粪池钢模具
U型槽钢模具
遮板钢模具
道轨模具
护坡钢模具
制砖机
检查井钢模具
声屏障钢模具
防撞墙钢模具
围墙板模具
方涵模具
锚杆框架梁模具
配重块模具
水泥三盘模具
水泥预制件模具
      新闻中心
· 检查井模具的施工工艺流程
· 排水井模具的使用过程简述
· 水泥检查井模具的使用过程介...
· 污水井模具的主要组成部分介...
· 检查井钢模具如何正确使用
· 排水井模具在使用中的注意事...
      联系我们

电话:0312-8103818 18803129528
传真:0312-8103818
在线QQ:107108222
地址:保定市城东工业区

     新闻中心

水泥检查井模具的使用过程介绍

[关闭该页][设为首页][添加收藏][发送朋友][打印][ ]

检查井模具整体是由三部分组成的:预留孔,调节圈,收口。水泥检查井模具是其中的一种叫法,也有的地方称观察井模具、渗水井模具、窖井模具、水泥井模具、下水井模具、阀门井模具、消防井模具、排水井模具等等,总之根据它的不同作用有好多叫法,但是制作过程其实都差不多。预留孔是用来连接地下容易发生故障而定期需要检修与维护的地方,如地下管道接头,弯头处,电缆等等。中间部分是调节圈,调节圈顾名思义就是用来调节整个井体在地下的高度,能够适应各种安装深度要求,有效降低了安装成本。整个井体的最上面就是收口部分,收口是与地面相齐平最后加上与收口直径相同的井盖,这样整个埋在地下的检查井就和地面保持齐平了。

Inspection well mold is composed of three parts: reserved hole, adjusting ring and closing. Cement inspection well mold is one of the methods. In some places, it is also called observation well mold, seepage well mold, cellar well mold, cement well mold, down well mold, valve well mold, fire well mold, drainage well mold, etc. in short, according to its different functions, there are many ways to call it, but the production process is actually similar. Reserved holes are used to connect underground places that are prone to failure and need regular maintenance, such as underground pipe joints, elbows, cables, etc. The middle part is the regulating ring, which, as the name implies, is used to adjust the height of the whole well in the underground, which can meet the requirements of various installation depths and effectively reduce the installation cost. The top part of the whole well body is the closing part, which is flush with the ground. Finally, a manhole cover with the same diameter as the closing in diameter is added, so that the whole buried inspection well is flush with the ground.

检查井模具使用过程中,需要注意施工人员在拼接模具时尽量使用电动扳手,因为拼接和拆除时一般只需要把模具连接处的螺栓拧紧和拆卸下来就可以了,特别的便捷,组装模具时需要保证每个螺栓拧的紧实模具之间不留缝隙,使用电动扳手拧紧,既能保证螺栓拧的够紧实,施工人员比起一个一个手动操作省时省力。2.在注入混凝土之前,需要在模具内均匀地涂抹工业机油,虽然模具的表面光滑,但是在注入刚搅拌好的混凝土之后不刷油的话,等混凝土凝固之后很容易与模具产生粘连的现象,刷洗的时候不但工作人员费时费力,而且还会减少模具的使用寿命。3.为了保证使用方形检查井模具制作生产出来的方形检查井使用时间长久,在注入混凝土时需要使用振动棒把混凝土内产生的气泡全部震动出来,使用完方形检查井模具之后,一定要及时的对模具进行清洗

In the process of using the inspection well mold, it is necessary to pay attention to the use of electric wrench by the construction personnel when splicing the mold. Generally, only the bolts at the joint of the mold need to be tightened and disassembled, which is especially convenient. When assembling the mold, it is necessary to ensure that each bolt is tightened tightly, and there is no gap between the molds. The use of electric wrench can ensure the bolt tightening Compared with a manual operation, the construction personnel can save time and labor. 2. Before pouring concrete, it is necessary to evenly apply industrial oil into the mold. Although the surface of the mold is smooth, it is easy to adhere to the mold after the concrete is solidified without oil painting. When brushing, it is not only time-consuming and laborious for the staff, but also can reduce the service life of the mold. 3. In order to ensure that the square inspection well produced by using the square inspection well mold has a long service life, it is necessary to use a vibrator to vibrate all the bubbles generated in the concrete when pouring concrete. After using the square inspection well mold, the mold must be cleaned in time.


【上一个】 排水井模具的使用过程简述 【下一个】 污水井模具的主要组成部分介绍


 · 水泥检查井模具的使用过程介绍 · 预制检查井模具的使用过程及作用
 · 预制检查井模具的生产标准有哪些 · 预制检查井模具的制作步骤

检查井钢模具,检查井模具,预制检查井模具——保定市晨泽模具制造有限公司 |隔离墩模具|排水沟模具|