产品列表
路沿石钢模具
盖板钢模具
标志桩钢模具
隔离墩钢模具
化粪池钢模具
U型槽钢模具
遮板钢模具
道轨模具
护坡钢模具
制砖机
检查井钢模具
声屏障钢模具
防撞墙钢模具
围墙板模具
方涵模具
锚杆框架梁模具
配重块模具
水泥三盘模具
水泥预制件模具
      新闻中心
· 预制井模具的成型方法
· 电力井模具的生产过程及使用...
· 污水井模具的生产制作过程
· 检查井模具的施工工艺流程
· 排水井模具的使用过程简述
· 水泥检查井模具的使用过程介...
      联系我们

电话:0312-8103818 18803129528
传真:0312-8103818
在线QQ:107108222
地址:保定市城东工业区

     新闻中心

排水井模具的使用过程简述

[关闭该页][设为首页][添加收藏][发送朋友][打印][ ]

排水井模具之所以使用钢模板,是因为钢模板有着很大的优势,排水井模具在焊接的时候,也能承受相对的应力,经受高速运转的振动平台也能保持不变形,我们在这个过程当中也要时时检查其使用效果。排水井模具使用了质量好的混凝土做预制产品,所以混凝土在使用的时候,也要注意一些情况,首先,混凝土不能放在高温的环境中,高温的条件会让混凝土丧失其原有的硬度和刚度,难以再次使用,施工之前要经过严谨的检查,在完工以后也要对混凝土制品进行浇水养护,让其更加坚固;其次,一些受潮的混凝土是不能投放到生产当中的,因为它的水分已经太多,会造成结硬结块的现象,失去使用效果,这些混凝土要经过筛选后再投放;再次,我们使用之前要经过搅拌搅实,不能在比较寒冷的条件下存放,否则会让里面的水分膨胀,混凝土质量遭到严重破坏。

The reason why steel formwork is used in drainage well mould is that steel formwork has great advantages. When welding, it can also bear relative stress, and the vibration platform can maintain no deformation under high-speed operation. In this process, we should always check its use effect. Inspection well steel mold uses good quality concrete as prefabricated products, so when using concrete, we should pay attention to some conditions. First of all, the concrete can not be placed in high temperature environment. High temperature conditions will make the concrete lose its original hardness and stiffness, which is difficult to use again. Before construction, we should go through strict inspection, and after the completion of the concrete products, we should also pay attention to some conditions Second, some wet concrete can not be put into the production because it has too much moisture, which will cause the phenomenon of caking and losing the use effect. These concrete should be put after screening. Thirdly, we should mix and mix before using, and can not be stored in cold conditions, otherwise it will give way The concrete quality is seriously damaged due to the water expansion on the surface.

排水井模具是要按照规定的流程进行操作,只有这样才能制作出合格的井筒预制件,当然在进行生产的时候也要注意好对于模具的一些保护,但是更主要的还是必须按照规定的方式进行模具的使用。

Drainage well mold is to operate in accordance with the specified process, only in this way can we produce qualified shaft prefabricated parts. Of course, we should pay attention to some protection for the mold during production, but more importantly, we must use the mold according to the specified way.

排水井模具使用过程:

1.需要使用螺栓进行模具的组装,螺栓的型号与规格是需要与将配套的,不能够胡乱使用组装的零件,并且拼装模具的时候,需要使用电动扳手将多块模具组装在一起,这样可以让螺栓将模具牢牢的固定,普通的螺栓工人在操作的时候比较的麻烦。2.每次生产之前井筒模具内是需要进行刷油的,刷油是指将油性的材料在模具的内里进行涂刷,避免泥浆直接的在模具的表面进行凝固。3.浇筑上泥浆后需要将振动棒插入到井筒模具中,对泥浆进行震动的处理,将气泡排出干净后就可以继续来进行晾晒了。

Using process of drainage well mould:

1. It is necessary to use bolts to assemble the mold. The model and specification of the bolts need to be matched with the parts to be assembled. When assembling the mold, it is necessary to use an electric wrench to assemble multiple molds together, so that the bolts can firmly fix the mold. Ordinary bolt workers are more troublesome in operation. 2. Before each production, it is necessary to brush oil in the wellbore mold. Oil painting refers to painting oily materials in the mold to avoid the mud directly solidifying on the surface of the mold. 3. After pouring the mud, it is necessary to insert the vibrator into the shaft mould to vibrate the mud. After the bubbles are discharged, it can be continued to dry.


【上一个】 检查井模具的施工工艺流程 【下一个】 水泥检查井模具的使用过程介绍


 · 排水井模具的使用过程简述 · 排水井模具在使用中的注意事项
 · 排水井模具的详细数据及加工步骤

检查井钢模具,检查井模具,预制检查井模具——保定市晨泽模具制造有限公司 |隔离墩模具|排水沟模具|